Kia Carens: Parking Brake System / Parking Brake Cable Repair procedures

Kia Carens RP (2013-2018) Service Manual / Brake System / Parking Brake System / Parking Brake Cable Repair procedures

Removal

The parking brake cables must not be bent or distorted. This will lead to stiff operation and premature failure.

1.	Remove the floor console assembly. (Refer to Body - "Floor console")

2.	Disconnect the connector (A) of parking brake switch.

Loosen the adjusting nut (A) and the parking brake cables (B).

Parking brake lever in the car must be in fully loosened position.

4.	Raise the vehicle, and make sure it is securely supported.

5.	Remove the rear tire and wheel.

6.	Remove the parking brake cable (A), after removing the clip (B).

7.	Loosen the parking brake cable bracket bolts and remove the parking brake cable (A).

Installation

Install the parking brake cable (A).

Tightening torque :

Bolts : 8.8 ~ 14.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

2.	Install the parking brake cable (A), and then install the clip (B).

3.	Install the rear tire and wheel.

4.	Install the parking brake cable (B).

Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.

Specified grease:

Multi purpose grease SAE J310, NLGI No.2

Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke:

5 ~ 7 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

7.	Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.

8.	Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.

Reconnect the connector (A) of parking brake switch.

Inspect the continuity of parking brake switch.

When the brake lever is pulled: continuity

When the brake lever is released: no continuity

10.	Install the floor console. (Refer to Body group - "Floor console")

Adjustment

Parking Brake Lever Stroke Adjustment

1.	Remove the storage service cover (A).

2.	Apply the brake pedal 20 times with the force of 10kgf after bleeding. Then, for the cable to settle in, apply the parking brake full stroke more than 3 times.

Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke :

6 ~ 8 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

4.	Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.

5.	Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.

6.	Install the storage service cover.

Parking Brake Lever Repair procedures

Removal The parking brake cables must not be bent or distorted. This will lead to stiff operation and prema ...

Electronic Parking Brake (EPB) Components and components location

Components 1. EPB Unit 2. EPB Switch 3. Brake Caliper 4. EPB Warning Lamp ...

Other information:

Kia Carens RP (2013-2018) Service Manual: Description and operation

Description Anti theft device Block diagram • BCM : Arming-Disarming data output • SIREN : Siren ON when disconnecting the battery, TILT & UIP sensor input • OFF switch : ...

Kia Carens RP (2013-2018) Service Manual: Fuel Sender Repair procedures

Removal 1. Remove the fuel pump. (Refer to Fuel Delivery System - "Fuel Pump") 2. Disconnect the fuel sender connector (A). 3. Remove the fuel sender (A) after releasing the fix hook. ...